John Deere D100, D105, D110, D120 Lawn Tractors Service Repair Manual -TM113219.pdf

D100, D105, D110, D120,
D125, D130, D140, D150,
D155, D160, and D170
Lawn Tractors Diagnostic
and Repair
TECHNICAL MANUAL
Lawn Tractors models D100, D110, D120, D130, D140, D150, D160, D170, D155,
D125, D105 (SN. 010001-)
TM113219 10 MAR 16 (ENGLISH)

John Deere Commercial and Consumer Equipment Lawn and Garden
Pinted by Belgreen

TM113219-TECHNICAL MANUAL (g) by Belgreen v2.5
<- Go to Global Table of contents TM113219-TECHNICAL MANUAL
Table of contents
FOREWORD
Section 10 - GENERAL INFORMATION
Group 05 - Safety
Group 20 - General Specifications
Group 15 - Fuel and Lubricants
Group 25 - Machine Specifications
Section 20 - SINGLE CYLINDER ENGINE REPAIR
Group 10 - Single Cylinder Engine Repair
Section 25 - V-TWIN ENGINE REPAIR
Group 10 - V-Twin Engine Repair
Section 30 - ELECTRICAL REPAIR
Group 10 - Component Location
Group 20 - Wiring Harnesses (Model Year -2011)
Group 25 - Wiring Harnesses (Model Year 2012)
Group 27 - Wiring Harnesses (Model Year 2013-)
Group 30 - Common Wiring Harnesses (All Model Years)
Section 40 - GEAR POWER TRAIN REPAIR
Group 10 - Gear Power Train Repair
Section 42 - CONTINUOUSLY VARIABLE TRANSMISSION (CVT) REPAIR, D105
Group 10 - CVT Repair
Section 45 - HYDROSTATIC POWER TRAIN REPAIR
Group 10 - Hydrostatic Power Train Repair
Section 50 - STEERING AND BRAKE REPAIR
Group 10 - Steering Repair
Group 20 - Brake Repair
Section 60 - ATTACHMENTS REPAIR
Group 15 - Attachments Repair
Section 70 - MISCELLANEOUS REPAIR
Group 10 - Miscellaneous Repair
Section 220 - SINGLE CYLINDER ENGINE OPERATION, TESTS, AND ADJUSTMENTS
Group 10 - Diagnostics
Group 20 - Tests and Adjustments
Section 225 - V-TWIN ENGINE OPERATION, TESTS, AND ADJUSTMENTS
Section 230 - ELECTRICAL OPERATION, TESTS, AND ADJUSTMENTS
Group 10 - Theory of Operation
Group 40 - Schematics (Model Year -2011)
Group 45 - Schematics (Model Year 2012-)
Group 50 - Connector Information
Section 240 - GEAR POWER TRAIN OPERATION, TESTS, AND ADJUSTMENTS
Section 242 - CONTINUOUSLY VARIABLE TRANSMISSION (CVT) OPERATION, D105

Section 245 - HYDROSTATIC POWER TRAIN OPERATION, TESTS, AND ADJUSTMENTS
Section 250 - STEERING AND BRAKE OPERATION, TESTS, AND ADJUSTMENTS
Group 10 - Steering Component Location
Group 20 - Steering Tests and Adjustments
Group 30 - Brake Component Location
Group 40 - Brake Tests and Adjustments
Section 260 - ATTACHMENTS OPERATION, TESTS, AND ADJUSTMENTS
Section 299 - SERVICE TOOLS AND KITS
Group 10 - Service Tools

GENERAL INFORMATION (g) by Belgreen v2.0
Section 10 page 1
<- Go to Section TOC TM113219-TECHNICAL MANUAL
Foreword
This manual is written for an experienced technician. Essential tools required in performing certain service work are identified
in this manual and are recommended for use.
Live with safety: Read the safety messages in the introduction of this manual and the cautions presented throughout the text
of the manual.
CAUTION:
This is the safety-alert symbol. When you see this symbol on the machine or in this manual, be alert to the potential for
personal injury.
Technical manuals are divided in two parts: repair and operation and tests. Repair sections tell how to repair the components.
Operation and tests sections help you identify the majority of routine failures quickly.
Information is organized in groups for the various components requiring service instruction. At the beginning of each group are
summary listings of all applicable essential tools, service equipment and tools, other materials needed to do the job, service
parts kits, specifications, wear tolerances, and torque values.
Technical Manuals are concise guides for specific machines. They are on-the-job guides containing only the vital information
needed for diagnosis, analysis, testing, and repair.
Fundamental service information is available from other sources covering basic theory of operation, fundamentals of
troubleshooting, general maintenance, and basic type of failures and their causes.

Section 10 - GENERAL INFORMATION
Table of contents
Group 05 - Safety..................................................................................................................................................... 1
Recognize Safety Information ....................................................................................... 1
Understand Signal Words
Follow Safety Instructions
Practice Safe Maintenance
. ......................................................................................... 1
. ......................................................................................... 1
......................................................................................... 3
Use Proper Tools....................................................................................................... 3
Handle Fluids Safely—Avoid Fires ................................................................................... 4
Drain Gasoline When Storing Machine.............................................................................. 4
Prevent Acid Burns .................................................................................................... 6
Prevent Battery Explosions ........................................................................................... 6
Handling Batteries Safely
Prepare for Emergencies
. ......................................................................................... 7
. .......................................................................................... 9
Park Machine Safely................................................................................................... 9
Support Machine Properly
Wear Protective Clothing
.......................................................................................... 9
. .........................................................................................11
Work in Clean Area ...................................................................................................11
Service Machines Safely
Work In Ventilated Area
...........................................................................................12
............................................................................................12
Illuminate Work Area Safely.........................................................................................12
Replace Safety Signs .................................................................................................13
Use Proper Lifting Equipment.......................................................................................13
Service Tires Safely...................................................................................................14
Decommissioning — Proper Recycling and Disposal of Fluids and Components ............................14
Protect Against High Pressure Spray...............................................................................15
Live With Safety ......................................................................................................16
Group 20 - General Specifications .....................................................................................................................17
Service Recommendations for O-Ring Boss Fittings.............................................................17
Service Recommendations For Flat Face O-Ring Seal Fittings................................................. 19
Metric Cap Screw Torque Values—Grade 7 .......................................................................20
Metric Bolt and Screw Torque Values ..............................................................................21
Unified Inch Bolt and Screw Torque Values .......................................................................22
Group 15 - Fuel and Lubricants.........................................................................................................................23
Engine Oil
Oil Filters
............................................................................................................23
.............................................................................................................23
Gasoline Fuel for 4-Cycle Engines ..................................................................................23
Transmission and Hydraulic Oil.....................................................................................24
Grease .................................................................................................................24
Mixing of Lubricants..................................................................................................24
Alternative and Synthetic Lubricants ..............................................................................25
Lubricant Storage ....................................................................................................25
Carburetor Cleaning..................................................................................................26
Carburetor Cleaning Methods .......................................................................................27
Group 25 - Machine Specifications ....................................................................................................................28
Machine Specifications..............................................................................................28
Product Identification Number Location...........................................................................29

Section 10 - GENERAL INFORMATION Group 05: Safety
Section 10 page 1
Group 05 - Safety
Recognize Safety Information
Safety-alert symbol
This is a safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal
injury.
Follow recommended precautions and safe operating practices.
Understand Signal Words
Signal Words
A signal word—DANGER, WARNING, or CAUTION—is used with the safety-alert symbol. DANGER identifies the most serious
hazards.
DANGER or WARNING safety signs are located near specific hazards. General precautions are listed on CAUTION safety signs.
CAUTION also calls attention to safety messages in this manual.
Follow Safety Instructions

Section 10 page 2
Safety Messages
Carefully read all safety messages in this manual and on your machine safety signs. Keep safety signs in good condition.
Replace missing or damaged safety signs. Be sure new equipment components and repair parts include the current safety
signs. Replacement safety signs are available from your John Deere dealer.
There can be additional safety information contained on parts and components sourced from suppliers that is not reproduced in
this operator′s manual.
Learn how to operate the machine and how to use controls properly. Do not let anyone operate without instruction.
Keep your machine in proper working condition. Unauthorized modifications to the machine may impair the function and/or
safety and affect machine life.
If you do not understand any part of this manual and need assistance, contact your John Deere dealer.

Section 10 page 3
Practice Safe Maintenance
Keep Area Clean
Understand service procedure before doing work. Keep area clean and dry.
Never lubricate, service, or adjust machine while it is moving. Keep hands, feet , and clothing from power-driven parts.
Disengage all power and operate controls to relieve pressure. Lower equipment to the ground. Stop the engine. Remove the
key. Allow machine to cool.
Securely support any machine elements that must be raised for service work.
Keep all parts in good condition and properly installed. Fix damage immediately. Replace worn or broken parts. Remove any
buildup of grease, oil, or debris.
On self-propelled equipment, disconnect battery ground cable (-) before making adjustments on electrical systems or welding
on machine.
On towed implements, disconnect wiring harnesses from tractor before servicing electrical system components or welding on
machine.
Use Proper Tools

Section 10 page 4
Proper Tools
Use tools appropriate to the work. Makeshift tools and procedures can create safety hazards.
Use power tools only to loosen threaded parts and fasteners.
For loosening and tightening hardware, use the correct size tools. DO NOT use U.S. measurement tools on metric fasteners.
Avoid bodily injury caused by slipping wrenches.
Use only service parts meeting John Deere specifications.
Handle Fluids Safely—Avoid Fires
Avoid Fires
When you work around fuel, do not smoke or work near heaters or other fire hazards.
Store flammable fluids away from fire hazards. Do not incinerate or puncture pressurized containers.
Make sure machine is clean of trash, grease, and debris.
Do not store oily rags; they can ignite and burn spontaneously.
Drain Gasoline When Storing Machine

Section 10 page 5
Storing Gasoline
Gasoline stored in fuel tank can explode.
Never store equipment with gasoline in the tank inside a building where fumes may reach an open flame or spark.
Always drain gasoline from fuel tank and carburetor bowl when storing machine. Allow engine to cool before storing.

Section 10 page 6
Prevent Acid Burns
Acid Burns
Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, eat holes in clothing, and cause blindness if
splashed into eyes.
Avoid the hazard by:
1. Filling batteries in a well-ventilated area.
2. Wearing eye protection and rubber gloves.
3. Avoiding breathing fumes when electrolyte is added.
4. Avoiding spilling or dripping electrolyte.
5. Use proper jump start procedure.
If you spill acid on yourself:
1. Flush your skin with water.
2. Apply baking soda or lime to help neutralize the acid.
3. Flush your eyes with water for 15—30 minutes. Get medical attention immediately.
If acid is swallowed:
1. Do not induce vomiting.
2. Drink large amounts of water or milk, but do not exceed 2 L (2 quarts).
3. Get medical attention immediately.
Prevent Battery Explosions

Section 10 page 7
Battery Explosions
Keep sparks, lighted matches, and open flame away from the top of battery. Battery gas can explode.
Never check battery charge by placing a metal object across the posts. Use a volt-meter or hydrometer.
Do not charge a frozen battery; it may explode. Warm battery to 16°C (60°F).
Handling Batteries Safely
Caution

Section 10 page 8
Caution
Battery gas can explode. Keep sparks and flames away from batteries. Use a flashlight to check battery electrolyte level.
Never check battery charge by placing a metal object across the posts. Use a voltmeter or hydrometer.
Always remove grounded (-) battery clamp first and replace grounded clamp last.
Sulfuric acid in battery electrolyte is poisonous and strong enough to burn skin, eat holes in clothing, and cause blindness if
splashed into eyes.
Avoid hazards by:
Filling batteries in a well-ventilated area
Wearing eye protection and rubber gloves
Avoiding use of air pressure to clean batteries
Avoiding breathing fumes when electrolyte is added
Avoiding spilling or dripping electrolyte
Using correct battery booster or charger procedure.
If acid is spilled on skin or in eyes:
1. Flush skin with water.
2. Apply baking soda or lime to help neutralize the acid.
3. Flush eyes with water for 15—30 minutes. Get medical attention immediately.
If acid is swallowed:
1. Do not induce vomiting.
2. Drink large amounts of water or milk, but do not exceed 2 L (2 qt.).
3. Get medical attention immediately.
WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State
of California to cause cancer and reproductive harm. Wash hands after handling.

Section 10 page 9
Prepare for Emergencies
First Aid Kit
Be prepared if a fire starts.
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance service, hospital, and fire department near your telephone.
Park Machine Safely
Remove the Key
Before working on the machine:
Lower all equipment to the ground.
Stop the engine and remove the key.
Disconnect the battery ground strap.
Hang a "DO NOT OPERATE" tag in operator station.
Support Machine Properly

Section 10 page 10
Support Properly
Always lower the attachment or implement to the ground before you work on the machine. If the work requires that the
machine or attachment be lifted, provide secure support for them. If left in a raised position, hydraulically supported devices
can settle or leak down.
Do not support the machine on cinder blocks, hollow tiles, or props that may crumble under continuous load. Do not work
under a machine that is supported solely by a jack. Follow recommended procedures in this manual.
When implements or attachments are used with a machine, always follow safety precautions listed in the implement or
attachment operator′s manual.

Section 10 page 11
Wear Protective Clothing
Protective Clothing
Wear close fitting clothing and safety equipment appropriate to the job.
Prolonged exposure to loud noise can cause impairment or loss of hearing.
Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud
noises.
Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating
machine.
Work in Clean Area
Clean Work Area
Before starting a job:
Clean work area and machine.
Make sure you have all necessary tools to do your job.
Have the right parts on hand.

Section 10 page 12
Read all instructions thoroughly; do not attempt shortcuts.
Service Machines Safely
Moving Parts
Tie long hair behind your head. Do not wear a necktie, scarf, loose clothing, or necklace when you work near machine tools or
moving parts. If these items were to get caught, severe injury could result.
Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts.
Work In Ventilated Area
Engine exhaust fumes
Engine exhaust fumes can cause sickness or death. If it is necessary to run an engine in an enclosed area, remove the exhaust
fumes from the area with an exhaust pipe extension.
If you do not have an exhaust pipe extension, open the doors and get outside air into the area.
Illuminate Work Area Safely

Section 10 page 13
Work Area Safely
Illuminate your work area adequately but safely. Use a portable safety light for working inside or under the machine. Make sure
the bulb is enclosed by a wire cage. The hot filament of an accidentally broken bulb can ignite spilled fuel or oil.
Replace Safety Signs
Safety Signs
Replace missing or damaged safety signs. See the machine operator’s manual for correct safety sign placement.
Use Proper Lifting Equipment
Proper Lifting Equipment
Lifting heavy components incorrectly can cause severe injury or machine damage.
Follow recommended procedure for removal and installation of components in the manual.

Section 10 page 14
Service Tires Safely
Explosive Tire and Rim Parts
Explosive separation of a tire and rim parts can cause serious injury or death.
Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job.
Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a
wheel and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion. Welding can structurally
weaken or deform the wheel.
When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of
or over the tire assembly. Use a safety cage if available.
Check wheels for low pressure, cuts, bubbles, damaged rims or missing lug bolts and nuts.
Decommissioning — Proper Recycling and Disposal of Fluids and
Components

Section 10 page 15
Recycle Waste
Safety and environmental stewardship measures must be taken into account when decommissioning a machine and/or
component. These measures include the following:
Use appropriate tools and personal protective equipment such as clothing, gloves, face shields or glasses, during the
removal or handling of objects and materials.
Follow instructions for specialized components.
Release stored energy by lowering suspended machine elements, relaxing springs, disconnecting the battery or other
electrical power, and releasing pressure in hydraulic components, accumulators, and other similar systems.
Minimize exposure to components which may have residue from agricultural chemicals, such as fertilizers and pesticides.
Handle and dispose of these components appropriately.
Carefully drain engines, fuel tanks, radiators, hydraulic cylinders, reservoirs, and lines before recycling components. Use
leak-proof containers when draining fluids. Do not use food or beverage containers.
Do not pour waste fluids onto the ground, down a drain, or into any water source.
Observe all national, state, and local laws, regulations, or ordinances governing the handling or disposal of waste fluids
(example: oil, fuel, coolant, brake fluid); filters; batteries; and, other substances or parts. Burning of flammable fluids or
components in other than specially designed incinerators may be prohibited by law and could result in exposure to
harmful fumes or ashes.
Service and dispose of air conditioning systems appropriately. Government regulations may require a certified service
center to recover and recycle air conditioning refrigerants which could damage the atmosphere if allowed to escape.
Evaluate recycling options for tires, metal, plastic, glass, rubber, and electronic components which may be recyclable, in
part or completely.
Contact your local environmental or recycling center, or your John Deere dealer for information on the proper way to
recycle or dispose of waste.
Protect Against High Pressure Spray
High Pressure Spray
Spray from high pressure nozzles can penetrate the skin and cause serious injury. Keep spray from contacting hands or body.
If an accident occurs, see a doctor immediately. Any high pressure spray injected into the skin must be surgically removed

Section 10 - GENERAL INFORMATION Group 20: General Specifications
Section 10 page 16
within a few hours or gangrene may result. Doctors unfamiliar with this type of injury should reference a knowledgeable
medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A.
Live With Safety
Safety Systems
Before returning machine to customer, make sure machine is functioning properly, especially the safety systems. Install all
guards and shields.

Section 10 page 17
Group 20 - General Specifications
Service Recommendations for O-Ring Boss Fittings
Straight Fitting
Straight Fitting
[1] - Inspect O-ring boss seat for dirt or defects.
[2] - Lubricate O-ring with petroleum jelly. Place electrical tape over threads to protect O-ring. Slide O-ring over tape and into
O-ring groove of fitting. Remove tape.
[3] - Tighten fitting to torque value shown on chart.
Angle Fitting
Angle Fitting
[1] - Back-off lock nut (A) and back-up washer (B) completely to head-end (C) of fitting.
[2] - Turn fitting into threaded boss until back-up washer contacts face of boss.
[3] - Turn fitting head-end counterclockwise to proper index (maximum of one turn).
[4] -
→NOTE:
Do not allow hoses to twist when tightening fittings.
Hold fitting head-end with a wrench and tighten locknut and back-up washer to proper torque value.

Section 10 page 18
Straight Fitting or Special Nut Torque Chart
STRAIGHT FITTING OR SPECIAL NUT TORQUE CHART
Thread Size N˙m lb-ft
3/8-24 UNF 8 6
7/16-20 UNF 12 9
1/2-20 UNF 16 12
9/16-18 UNF 24 18
3/4-16 UNF 46 34
7/8-14 UNF 62 46
1-1/16-12 UN 102 75
1-3/16-12 UN 122 90
1-5/16-12 UN 142 105
1-5/8-12 UN 190 140
1-7/8-12 UN 217 160
→NOTE:
Torque tolerance is ± 10%.

Section 10 page 19
Service Recommendations For Flat Face O-Ring Seal Fittings
[1] - Inspect the fitting sealing surfaces and O-ring. They must be free of dirt or defects.
[2] - Lubricate O-rings and install into grove using petroleum jelly to hold in place.
[3] - Index angle fittings and tighten by hand pressing joint together to insure O-ring remains in place.
[4] - Tighten fitting or nut to torque value shown on the chart. Do not allow hoses to twist when tightening fittings, use backup
wrench on straight hose couplings.
IMPORTANT:
Tighten fittings to 150% of listed torque value if indexing is necessary or if fitting is attached to an
actuating device.
Tighten fittings to 50% of listed torque value if used in aluminum housing.
O-ring Seal Fitting Torque
FLAT FACE O-RING SEAL FITTING TORQUE*
Nomial Tube O.D. Thread Size Swivel Nut Bulkhead Nut
mm in. in. N˙m lb·ft N˙m lb·ft
6.35 0.250 9/16-18 16 12 12 9
9.52 0.375 11/16-16 24 18 24 18
12.70 0.500 13/16-16 50 37 46 34
15.88 0.625 1-14 69 51 62 46
19.05 0.750 1 3/16-12 102 75 102 75
22.22 0.875 1 3/16-12 102 75 102 75
25.40 1.000 1 7/16-12 142 105 142 105
31.75 1.250 1 11/16-12 190 140 190 140
38.10 1.500 2-12 217 160 217 160
*Torque tolerance is +15 -20% unless otherwise specified.
Stud End O-ring Seal Torque for Straight and Adjustable Fittings*
Thread Size Straight Hex Size Locknut Hex Size Straight Fitting or Locknut Toque
Inch Inch Inch N˙m lb·ft
3/8-24 5/8 9/16 12 9
7/16-20 5/8 5/8 21 15
1/2-20 3/4 11/16 26 19
9/16-18 3/4 3/4 34 25
3/4-16 7/8 15/16 73 55
7/8-14 1 1/16 1 1/16 104 76
1 1/16-12 1 1/4 1 3/8 176 130
1 3/16-12 1 3/8 1 1/2 230 170
1 5/16-12 1 1/2 1 5/8 285 210
*Torque tolerance is +15 -20% unless otherwise specified.

Section 10 page 20
Metric Cap Screw Torque Values—Grade 7
→NOTE:
When bolting aluminum parts, tighten to 80% of torque specified in table.
Metric Cap Screw Torque Values—Grade 7
Size N˙m (lb-ft)
M6 9.5—12.2 (7—9)
M8 20.3—27.1 (15—20)
M10 47.5—54.2 (35—40)
M12 81.4—94.9 (60—70)
M14 128.8—146.4 (95—108)
M16 210.2—240 (155—177)

Section 10 page 21
Metric Bolt and Screw Torque Values
Metric Bolt and Screw
Metric Torque Values
Class 4.8 Class 8.8 or 9.8 Class 10.9 Class 12.9
Lubricated
Dry
[ “Dry” means
plain or zinc
plated without
any lubrication, or
M6 to M18
fasteners with
JDM F13B, F13E or
F13H zinc flake
coating. ]
Lubricated
Dry
[ “Dry” means
plain or zinc
plated without
any lubrication, or
M6 to M18
fasteners with
JDM F13B, F13E or
F13H zinc flake
coating. ]
Lubricated
Dry
[ “Dry” means
plain or zinc
plated without
any lubrication, or
M6 to M18
fasteners with
JDM F13B, F13E or
F13H zinc flake
coating. ]
Lubricated
Dry
[ “Dry” means
plain or zinc
plated without
any lubrication, or
M6 to M18
fasteners with
JDM F13B, F13E or
F13H zinc flake
coating. ]
[ “Lubricated” [ “Lubricated” [ “Lubricated” [ “Lubricated”
means coated with means coated with means coated with means coated with
Bolt or
Screw
a lubricant such as
engine oil,
fasteners with
a lubricant such as
engine oil,
fasteners with
a lubricant such as
engine oil,
fasteners with
a lubricant such as
engine oil,
fasteners with
Size phosphate and oil
coatings, or M20
phosphate and oil
coatings, or M20
phosphate and oil
coatings, or M20
phosphate and oil
coatings, or M20
and larger and larger and larger and larger
fasteners with JDM fasteners with JDM fasteners with JDM fasteners with JDM
F13C, F13F or F13J F13C, F13F or F13J F13C, F13F or F13J F13C, F13F or F13J
zinc flake coating. zinc flake coating. zinc flake coating. zinc flake coating.
] ] ] ]
N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in.
M6 4.7 42 6 53 8.9 79 11.3 100 13 115 16.5 146 15.5 137 19.5 172
N˙m lb.-ft. N˙m lb.-ft. N˙m lb.-ft. N˙m lb.-ft.
M8 11.5 102 14.5 128 22 194 27.5 243 32 23.5 40 29.5 37 27.5 47 35
N˙m lb.-ft. N˙m lb.-ft. N˙m lb.-ft.
M10 23 204 29 21 43 32 55 40 63 46 80 59 75 55 95 70
N˙m lb.-ft.
M12 40 29.5 50 37 75 55 95 70 110 80 140 105 130 95 165 120
M14 63 46 80 59 120 88 150 110 175 130 220 165 205 150 260 190
M16 100 74 125 92 190 140 240 175 275 200 350 255 320 235 400 300
M18 135 100 170 125 265 195 330 245 375 275 475 350 440 325 560 410
M20 190 140 245 180 375 275 475 350 530 390 675 500 625 460 790 580
M22 265 195 330 245 510 375 650 480 725 535 920 680 850 625 1080 800
M24 330 245 425 315 650 480 820 600 920 680 1150 850 1080 800 1350 1000
M27 490 360 625 460 950 700 1200 885 1350 1000 1700 1250 1580 1160 2000 1475
M30 660 490 850 625 1290 950 1630 1200 1850 1350 2300 1700 2140 1580 2700 2000
M33 900 665 1150 850 1750 1300 2200 1625 2500 1850 3150 2325 2900 2150 3700 2730
M36 1150 850 1450 1075 2250 1650 2850 2100 3200 2350 4050 3000 3750 2770 4750 3500
Torque values listed are for general use only, based on the strength of the
bolt or screw. DO NOT use these values if a different torque value or
tightening procedure is given for a specific application. For stainless steel
fasteners or for nuts on U-bolts, see the tightening instructions for the
specific application. Tighten plastic insert or crimped steel type lock nuts by
turning the nut to the dry torque shown in the chart, unless different
instructions are given for the specific application.
Shear bolts are designed to fail under predetermined loads. Always replace shear bolts
with identical property class. Replace fasteners with the same or higher property class.
If higher property class fasteners are used, tighten these to the strength of the original.
Make sure fastener threads are clean and that you properly start thread engagement.
When possible, lubricate plain or zinc plated fasteners other than lock nuts, wheel bolts
or wheel nuts, unless different instructions are given for the specific application.

Section 10 - GENERAL INFORMATION Group 15: Fuel and Lubricants
Section 10 page 22
Unified Inch Bolt and Screw Torque Values
Unified Inch Bolt and Screw
Unified Inch Bolt and Screw Torque Values
Bolt or
Screw
Size
SAE Grade 1
SAE Grade 2
[ Grade 2 applies for hex cap screws
(not hex bolts) up to 6 in. (152 mm)
long. Grade 1 applies for hex cap screws
over 6 in. (152 mm) long, and for all
other types of bolts and screws of any
length. ]
SAE Grade 5, 5.1 or 5.2 SAE Grade 8 or 8.2
Lubricated
[ “Lubricated”
means coated
with a lubricant
such as engine
oil, fasteners with
phosphate and oil
coatings, or 7/8
in. and larger
fasteners with
JDM F13C, F13F or
F13J zinc flake
coating. ]
Dry
[ “Dry” means
plain or zinc
plated without
any lubrication, or
1/4 to 3/4 in.
fasteners with
JDM F13B, F13E or
F13H zinc flake
coating. ]
Lubricated
[ “Lubricated”
means coated with
a lubricant such as
engine oil,
fasteners with
phosphate and oil
coatings, or 7/8 in.
and larger
fasteners with JDM
F13C, F13F or F13J
zinc flake coating.
]
Dry
[ “Dry” means
plain or zinc plated
without any
lubrication, or 1/4
to 3/4 in. fasteners
with JDM F13B,
F13E or F13H zinc
flake coating. ]
Lubricated
[ “Lubricated”
means coated with
a lubricant such as
engine oil,
fasteners with
phosphate and oil
and larger
fasteners with JDM
F13C, F13F or F13J
zinc flake coating.
]
Dry
[ “Dry” means
plain or zinc
plated without
any lubrication, or
1/4 to 3/4 in.
fasteners with
JDM F13B, F13E or
F13H zinc flake
coating. ]
Lubricated
[ “Lubricated”
means coated with
a lubricant such as
engine oil,
fasteners with
phosphate and oil
and larger
fasteners with JDM
F13C, F13F or F13J
zinc flake coating.
]
Dry
[ “Dry” means
plain or zinc
plated without
any lubrication, or
1/4 to 3/4 in.
fasteners with
JDM F13B, F13E or
F13H zinc flake
coating. ]
N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in. N˙m lb.-in.
1/4 3.7 33 4.7 42 6 53 7.5 66 9.5 84 12 106 13.5 120 17 150
N˙m lb.-ft. N˙m lb.-ft.
5/16 7.7 68 9.8 86 12 106 15.5 137 19.5 172 25 221 28 20.5 35 26
N˙m lb.-ft. N˙m lb.-ft.
3/8 13.5 120 17.5 155 22 194 27 240 35 26 44 32.5 49 36 63 46
N˙m lb.-ft. N˙m lb.-ft. N˙m lb.-ft.
7/16 22 194 28 20.5 35 26 44 32.5 56 41 70 52 80 59 100 74
N˙m lb.-ft.
1/2 34 25 42 31 53 39 67 49 85 63 110 80 120 88 155 115
9/16 48 35.5 60 45 76 56 95 70 125 92 155 115 175 130 220 165
5/8 67 49 85 63 105 77 135 100 170 125 215 160 240 175 305 225
3/4 120 88 150 110 190 140 240 175 300 220 380 280 425 315 540 400
7/8 190 140 240 175 190 140 240 175 490 360 615 455 690 510 870 640
1 285 210 360 265 285 210 360 265 730 540 920 680 1030 760 1300 960
1-1/8 400 300 510 375 400 300 510 375 910 670 1150 850 1450 1075 1850 1350
1-1/4 570 420 725 535 570 420 725 535 1280 945 1630 1200 2050 1500 2600 1920
1-3/8 750 550 950 700 750 550 950 700 1700 1250 2140 1580 2700 2000 3400 2500
1-1/2 990 730 1250 930 990 730 1250 930 2250 1650 2850 2100 3600 2650 4550 3350
Torque values listed are for general use only, based on the strength of the bolt or
screw. DO NOT use these values if a different torque value or tightening procedure is
given for a specific application. For plastic insert or crimped steel type lock nuts, for
stainless steel fasteners, or for nuts on U-bolts, see the tightening instructions for the
specific application. Shear bolts are designed to fail under predetermined loads. Always
replace shear bolts with identical grade.
Replace fasteners with the same or higher grade. If higher grade fasteners
are used, tighten these to the strength of the original. Make sure fastener
threads are clean and that you properly start thread engagement. When
possible, lubricate plain or zinc plated fasteners other than lock nuts, wheel
bolts or wheel nuts, unless different instructions are given for the specific
application.

Section 10 page 23
Group 15 - Fuel and Lubricants
Engine Oil
Use oil viscosity based on the expected air temperature range during the period between oil changes.
Oil Chart
The following John Deere oils are preferred:
TURF-GARD™
PLUS- 4™
Other oils may be used if above John Deere oils are not available, provided they meet the following specification:
API Service Classification SJ or higher
Oil Filters
Filtration of oils is critical to proper operation and lubrication.
Always change filters regularly as specified in this manual.
Use filters meeting John Deere performance specifications.
Gasoline Fuel for 4-Cycle Engines
Use unleaded gasoline with a minimum octane rating of 87 AKI (anti-knock index) or 90 RON (research octane number).
Gasoline fuels specified to EN 228 or ASTM D4814 are recommended.
Fuel blends of unleaded gasoline with a maximum 10% ethanol or 15% MTBE (methyl tertiary-butyl ether) are also acceptable.
CAUTION:
Reduce the risk of fire. Handle fuel carefully. DO NOT fill the fuel tank when the engine is running or hot.
Stop engine and allow it to cool for several minutes before filling fuel tank. Fill fuel tank only to the
bottom of the filler neck.
Refuel outdoors. DO NOT smoke while you fill the fuel tank or service the fuel system.
Store fuel in properly identified polyethylene containers.
When storing fuel, add John Deere Gasoline Conditioner and Stabilizer (or equivalent) at the specified concentration.
IMPORTANT:
DO NOT use methanol or fuel blends that contain methanol.
Avoid spilling fuel. Gasoline can damage plastic and painted surfaces.
DO NOT mix oil with gasoline.

Section 10 page 24
Transmission and Hydraulic Oil
Transmission and Hydraulic Oil
Use oil viscosity based on the expected air temperature range during the period between oil changes.
The following oils are preferred:
John Deere HY-GARD ™
John Deere Low Viscosity HY-GARD ™
Other oils may be used if they meet one of the following:
John Deere Standard JDM J20C
John Deere Standard JDM J20D
Use John Deere BIO-HY-GARD ™ oil when a biodegradable fluid is required.
[ BIO-HY-GARD meets or exceeds the minimum biodegradability of 80% within 21 days according to CEC-L-33-T-82 test method. BIO-HY-GARD should not be mixed with mineral oils, because this reduces
the biodegradability and makes proper oil recycling impossible. ]
Grease
IMPORTANT:
Avoid Damage! Use recommended John Deere greases to avoid component failure and premature wear.
The following grease is recommended for service:
John Deere Multi-Purpose HD Lithium Complex Grease
Grease-Gard™ Premium Plus
Not all grease types are compatible; John Deere does not recommend mixing greases. If using any product other than the
recommended grease in service, purge any remaining grease from the system prior to application. If this is not practical,
grease twice as often until all old grease is purged from the system.
Mixing of Lubricants
In general, avoid mixing different brands or types of oil. Oil manufacturers blend additives in their oils to meet certain
specifications and performance requirements.
Mixing different oils can interfere with the proper functioning of these additives and degrade lubricant performance.
Consult your John Deere dealer to obtain specific information and recommendations.

John Deere D100, D105, D110, D120 Lawn Tractors Service Repair Manual -TM113219.pdf

Related slideshows

More Related Content

Similar to John Deere D100, D105, D110, D120 Lawn Tractors Service Repair Manual -TM113219.pdf

Similar to John Deere D100, D105, D110, D120 Lawn Tractors Service Repair Manual -TM113219.pdf (13)

More from Excavator

More from Excavator (20)

Recently uploaded

Recently uploaded (20)

John Deere D100, D105, D110, D120 Lawn Tractors Service Repair Manual -TM113219.pdf